I discovered that the gmp functions use [0-9a-f] up to base 16, but [0-9A-Za-z] (i.e. upper case first) from bases 17 to 62. This differs from most of the base-62 implementations I've found that tend to use lower case first.
(PHP 4 >= 4.0.4, PHP 5, PHP 7, PHP 8)
gmp_init — Crea un número GMP
number
Un entero o cadena. La representación de la cadena puede ser decimal, hexadecimal or octal.
base
La base.
La base puede variar de 2 a 36. Si la base es 0 (valor por defecto), la
actual base es determinada de los caracteres lideres: si los primeros
dos caracteres son 0x
o 0X
,
el hexadecimal es asumido, sin embargo si el primer carácter es "0",
el octal es asumido, sin embargo el decimal es asumido.
resource de número de GMP en PHP 5.5 y anterior, o un objeto GMP en PHP 5.6 y posterior.
Versión | Descripción |
---|---|
5.3.2 |
La base fue extendidad de 2 a 36, a
2 a 62 y -2 a -36.
|
Nota:
Para usar la base extendidad introducida en PHP 5.3.2, entonces PHP tiene que ser compilado en contra de GMP 4.2.0 o superior.
Ejemplo #1 Creación de un número GMP
<?php
$a = gmp_init(123456);
$b = gmp_init("0xFFFFDEBACDFEDF7200");
?>
Nota:
No es necesario llamar ésta función si se desea usar un entero o cadena en lugar de un número GMP en una función GMP, como gmp_add(). Los argumentos de la función son automáticamente convertidos a números GMP, si tal conversión es posible y necesaria, usando las mismas reglas como gmp_init().
I discovered that the gmp functions use [0-9a-f] up to base 16, but [0-9A-Za-z] (i.e. upper case first) from bases 17 to 62. This differs from most of the base-62 implementations I've found that tend to use lower case first.
Here's a way to parse a decimal (eg 3.25) into an integer and exponent:
<?
if (preg_match("/^[0-9]+\.[0-9]+$/",$input)){
//Input is a base-10 decimal. Multiply as necessary to remove the decimal
//point. Convert that to a gmp_resource, then decrement the exponent
//to compensate.
$pieces=explode(".", $input); //Split at the d.p.
$input="$pieces[0]$pieces[1]"; //Remove the decimal point.
$input=ltrim($input,'0');
//Remove any leading zeros, or gmp_init will parse the number as octal.
if ($input==''){ //Deal with "0.0" which would otherwise be ''.
$input=0;
}
$integer=gmp_init($input);
$ns_exponent=-strlen($pieces[1]);
//exponent = (-) the number of characters after the decimal point.
}
?>
Note: Leading zeros will make gmp_init parse this as octal.
Thus gmp_init(010) becomes 8.
$a=010; //8
$b="010" + 0; //10
$c=gmp_strval(gmp_init(010)); //8
$d=gmp_strval(gmp_init("010")); //8
This behaviour is inconsistent: either $d should equal $b, or
$b should equal $a.
Unless the base is 16, gpm_init will fail if the string begins with "0b".
> php -r '$v = gmp_init("b83", 17); print("$v\n");'
Resource id #4
> php -r '$v = gmp_init("0b83", 17); print("$v\n");'
[nothing prints]
In may case, where I am explicitly specifying the base, the solution is to apply ltrim first:
> php -r '$v = gmp_init(ltrim("0b83", "0"), 17); print("$v\n");'
Resource id #4
gmp_* functions don't accept strings with a leading '+':
<?php
echo gmp_strval(gmp_init('+42')); #0
echo gmp_strval(gmp_add('42', '+42')); #42
echo bcadd('+42', '+42'); #84
?>
If you call a gmp_* function directly with an interger as parameter, this integer MUST NOT be 0:
for($i=-1;$i<=1;$i++) { echo gmp_strval(gmp_add(2,gmp_mul(1,$i))) . ' '; }
The result is 1 0 3 (wrong)
In this case you have to use gmp_init():
for($i=-1;$i<=1;$i++) { echo gmp_strval(gmp_add(2,gmp_mul(1,gmp_init($i)))) . ' '; }
The result is 1 2 3 (right)
Happy number crunching! :-)